Dongguan Zhaoshun Silicone Technology CO., LTD

First, product features

ZS-NJ-D933L medium viscosity component removal alcohol type room temperature curing silicone adhesive sealant, transparent adhesive sealing good connection, good adhesion of aluminum, copper, stainless steel and other metals; superior electrical properties, good heat resistance, general use temperature range of - 60 DEG C ~ 200 DEG C. The release of the transparent sealant in the curing process is alcohol, PC, copper and other materials without corrosion, in full compliance with the EU ROHS directive requirements.

Two, typical use

The bonding and sealing of the electronic circuit board, the bonding and sealing of the engineering plastics, metal, glass and ceramic objects, and the bonding and positioning of the electronic components on the electronic circuit board and the strengthening and moisture sealing. Waterproof sealing instrument, encapsulating module protection; 6mm thickness small, thin electronic components, module, photoelectric display and circuit board encapsulation protecting.

Three, technical parameters

solid

turn

Before the appearance of semi transparent semi flowing

Relative density (g/cm3) 0.95 ~ 1.05

Dry time table (min) is less than or equal to 15

Complete cure time (d) 3 ~ 7

solid

turn

The tensile strength (MPa = 0.5)

Elongation (%) = 200

Shear strength (MPa = 0.5)

Hardness (A Shore) 15 ~ 25

Temperature range (c) -60 ~ 200

Volume resistivity (CM) 1015 * 2.6

Dielectric strength (kV/mm) 20

Dielectric constant (1.2MHz) 3.12

The above performance data are at 25 degrees Celsius, the relative humidity 55% curing 7 days after the test. The company's test conditions are different or product improvement caused by different data does not bear the responsibility.

Four, the use of Technology

1: clean the surface will be sticky or coated with the surface clean and remove rust, dust and oil etc..

2, sizing: unscrew (or cut open) hose cap, glue squeeze to have to clean up the surface, enabling the distribution uniformity, will be the sticky surface closure solid

Set.

3, curing: will be adhered to good or sealed parts in the air to let the natural curing. Curing process is a cure from the surface to the inside.

Process, within 24 hours (room temperature and 55% relative humidity) glue will solidify the depth of 2 ~ 4mm, if the location is deeper, especially in the

Easily exposed to the air, the time will be fully cured, if the temperature is low, the curing time will be extended. In making further

Prior to processing or to be bonded to the component, it is recommended that the user wait long enough to keep the adhesion and integrity of the bond from being affected.

Sealant is completely cured for 7 days or more time.

Five, matters needing attention

After the transparent sealant is completed, the non used transparent sealant should be tightened immediately and sealed. Once again, if the seal is a little skin, remove it, do not affect the normal use of the. Glue in the process of storage, mouth also may be a small amount of curing phenomenon, will be cleared after normal use, does not affect the transparent sealant properties.

Six, packaging specifications

100ml/ branch, 100 branch / box; 300ml/ branch, 25 branch / box.

Seven, storage and transportation

1, 25 degrees Celsius in a cool and dry environment for 6 months, more than the shelf life of the transparent sealant should be recognized without exception before use.

2, such products are non - hazardous transparent sealant, according to the general chemical transport. Be careful in the course of transportation!

Eight, recommendations and statements

It is recommended that the user do the test before the use of transparent sealant. Due to the diversity of practical application, our company does not guarantee specific conditions using our products appear problem, assume no responsibility for any direct, indirect or consequential or incidental damages, the user in the use of the process encountered any problems, contact our after-sales service department. We will strive to provide you with help.

Zhaoshun technology supply: transparent sealant

Product detail page: http://www.megasun-tech.com/about.html

Contact: Zheng Zhen

QQ:2731870546

Tel: 0769-88888312

Cell phone: 15112798306

Alibaba: www.zsilicone.cn

Source: Dongguan Zhaoshun silicone Polytron Technologies Inc

Zhao shun technology 15 years of silicone professional manufacturer, attention to electronics, led, home appliance, solar photovoltaic and industry, with clients provided all outstanding applications of experience, has a strong product development capabilities, get the industry recognized!