Dongguan Zhaoshun Silicone Technology CO., LTD

First, product features

ZS-NJ-D959W is a single component dealcoholization type room temperature curing silicone sealant. Inductance core special adhesive with flame retardant effect of heat conduction, good adhesion, for a variety of metal aluminum, copper, stainless steel has good adhesion; superior dielectric properties, good heat resistance, general use temperature range of - 60 DEG C to 200 degrees. The release of the curing process is alcohol, the polycarbonate (PC), copper and other materials without corrosion, in full compliance with the EU ROHS directive requirements.

Two, typical use

Electronic, electrical components, fixed and flame retardant, heat conduction, insulation, shock proof, moisture proof seal.

Three, technical parameters

solid

turn

Before the appearance of white paste

Relative density (g/cm3) 2.10 ~ 2.20

Dry time table (min) is less than or equal to 20

Complete cure time (d) 3 ~ 7

solid

turn

The tensile strength (MPa = 2)

Elongation (%) = 120

Shear strength (MPa = 0.6)

Hardness (A Shore) 55 ~ 65

Temperature range (c) -60 ~ 200

Volume resistivity (CM) 1014 * 2

Dielectric strength (kV/mm) 20

The thermal conductivity of W/ (M - K) was more than 0.8

The above performance data are at 25 degrees Celsius, the relative humidity 55% curing 7 days after the test. The company's test conditions are different or product improvement caused by different data does not bear the responsibility.

Four, the use of Technology

1: clean the surface will be sticky or coated with the surface clean and remove rust, dust and oil etc..

2, sizing: unscrew (or cut open) hose cap, glue squeeze to have to clean up the surface, enabling the distribution uniformity, will be the sticky surface closure

Fixed.

3, curing: will be adhered to good or sealed parts in the air to let the natural curing. Curing process is a cure from the surface to the inside.

Process, within 24 hours (room temperature and 55% relative humidity) glue will solidify the depth of 2 ~ 4mm, if the location is deeper, especially in the

Easily exposed to the air, the time will be fully cured, if the temperature is low, the curing time will be extended. In making further

Prior to processing or to be bonded to the component, it is recommended that the user wait long enough to keep the adhesion and integrity of the bond from being affected.

Sealant is completely cured for 7 days or more time.

Five, matters needing attention

After the application of the special adhesive for the inductor and the magnetic core is completed, the special adhesive for the magnetic core of the magnetic core is not used, and the cap is tightened immediately. Once again, if the seal is a little skin, remove it, do not affect the normal use of the. Inductance core special glue in the process of storage, mouth also may appear the phenomenon of a small amount of curing, will be cleared after normal use, does not affect the performance of the products.

Six, packaging specifications

300ml/ branch, 25 branch / box.

Seven, storage and transportation

25, 1 degrees Celsius below the cool and dry environment for 6 months, more than the shelf life of the inductor magnetic core should be recognized without exception before use.

2, the inductance of the magnetic core is a non - dangerous goods, according to the general chemical transport. Be careful in the course of transportation!

Eight, recommendations and statements

It is recommended that the user first apply the test before the use of the inductor core special adhesive. Due to the diversity of practical application, our company does not guarantee specific conditions using our products appear problem, assume no responsibility for any direct, indirect or consequential or incidental damages, the user in the use of the process encountered any problems, contact our after-sales service department. We will strive to provide you with help.

Zhaoshun technology supply: special inductcore glue

Product detail page: http://www.megasun-tech.com/about.html

Contact: Zheng Zhen

QQ:2731870546

Tel: 0769-88888312

Cell phone: 15112798306

Alibaba: www.zsilicone.cn

Source: Dongguan Zhaoshun silicone Polytron Technologies Inc

Zhao shun technology 15 years of silicone professional manufacturer, attention to electronics, led, home appliance, solar photovoltaic and industry, with clients provided all outstanding applications of experience, has a strong product development capabilities, get the industry recognized!