1.Identification
1.1 GHS Product identifier
Product name | fluoroethene |
---|
1.2 Other means of identification
Product number | - |
---|---|
Other names | 1-fluoroethylene |
1.3 Recommended use of the chemical and restrictions on use
Identified uses | For industry use only. Intermediates |
---|---|
Uses advised against | no data available |
1.4 Supplier's details
Company | MOLBASE (Shanghai) Biotechnology Co., Ltd. |
---|---|
Address | Floor 4 & 5, Building 12, No. 1001 North Qinzhou Road, Xuhui District, Shanghai, China |
Telephone | +86(21)64956998 |
Fax | +86(21)54365166 |
1.5 Emergency phone number
Emergency phone number | +86-400-6021-666 |
---|---|
Service hours | Monday to Friday, 9am-5pm (Standard time zone: UTC/GMT +8 hours). |
2.Hazard identification
2.1 Classification of the substance or mixture
Flammable gases, Category 1
Gases under pressure: Liquefied gas
Germ cell mutagenicity, Category 2
Carcinogenicity, Category 1B
Specific target organ toxicity – repeated exposure, Category 2
2.2 GHS label elements, including precautionary statements
Pictogram(s) | ![]() ![]() |
---|---|
Signal word | Danger |
Hazard statement(s) | H220 Extremely flammable gas H280 Contains gas under pressure; may explode if heated H341 Suspected of causing genetic defects H350 May cause cancer H373 May cause damage to organs through prolonged or repeated exposure |
Precautionary statement(s) | |
Prevention | P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P201 Obtain special instructions before use. P202 Do not handle until all safety precautions have been read and understood. P280 Wear protective gloves/protective clothing/eye protection/face protection. P260 Do not breathe dust/fume/gas/mist/vapours/spray. |
Response | P377 Leaking gas fire: Do not extinguish, unless leak can be stopped safely. P381 In case of leakage, eliminate all ignition sources. P308+P313 IF exposed or concerned: Get medical advice/ attention. P314 Get medical advice/attention if you feel unwell. |
Storage | P403 Store in a well-ventilated place. P410+P403 Protect from sunlight. Store in a well-ventilated place. P405 Store locked up. |
Disposal | P501 Dispose of contents/container to ... |
2.3 Other hazards which do not result in classification
none
3.Composition/information on ingredients
3.1 Substances
Chemical name | Common names and synonyms | CAS number | EC number | Concentration |
---|---|---|---|---|
fluoroethene | fluoroethene | 75-02-5 | none | 100% |
4.First-aid measures
4.1 Description of necessary first-aid measures
General advice
Consult a physician. Show this safety data sheet to the doctor in attendance.
If inhaled
Fresh air, rest.
In case of skin contact
ON FROSTBITE: rinse with plenty of water, do NOT remove clothes.
In case of eye contact
First rinse with plenty of water for several minutes (remove contact lenses if easily possible), then refer for medical attention.
If swallowed
Never give anything by mouth to an unconscious person. Rinse mouth with water. Consult a physician.
4.2 Most important symptoms/effects, acute and delayed
Inhalation of vapor causes slight intoxication, some shortness of breath. Liquid may cause frostbite of eyes or skin. (USCG, 1999)
4.3 Indication of immediate medical attention and special treatment needed, if necessary
Basic treatment: Establish a patent airway. Suction if necessary. Watch for signs of respiratory insufficiency and assist ventilations if necessary. Administer oxygen by nonrebreather mask at 10 to 15 L/min. Monitor for pulmonary edema and treat if necessary ... . Monitor for shock and treat if necessary ... . Anticipate seizures and treat if necessary ... . For eye contamination, flush eyes immediately with water. Irrigate each eye continuously with normal saline during transport ... . Do not use emetics. For ingestion, rinse mouth and administer 5 ml/kg up to 200 ml of water for dilution if the patient can swallow, has a strong gag reflex, and does not drool. Administer activated charcoal ... . Cover skin burns with sterile dressings after decontamination ... . /Halogenated aliphatic hydrocarbons and related compounds/
5.Fire-fighting measures
5.1 Extinguishing media
Suitable extinguishing media
If material on fire or involved in fire: Do not extinguish fire unless flow can be stopped. Use water in flooding quantities as fog. Cool all affected containers with flooding quantities of water. Apply water from as far a distance as possible. /Vinyl fluoride, stabilized/
5.2 Specific hazards arising from the chemical
Special Hazards of Combustion Products: Toxic hydrogen fluoride gas is generated in a fire. Behavior in Fire: Vapor is heavier than air and may travel considerable distance to a source of ignition and flash back. Containers may explode. (USCG, 1999)
5.3 Special protective actions for fire-fighters
Wear self-contained breathing apparatus for firefighting if necessary.
6.Accidental release measures
6.1 Personal precautions, protective equipment and emergency procedures
Use personal protective equipment. Avoid dust formation. Avoid breathing vapours, mist or gas. Ensure adequate ventilation. Evacuate personnel to safe areas. Avoid breathing dust. For personal protection see section 8.
6.2 Environmental precautions
Evacuate danger area! Consult an expert! Ventilation. NEVER direct water jet on liquid. Personal protection: self-contained breathing apparatus.
6.3 Methods and materials for containment and cleaning up
PRECAUTIONS FOR "CARCINOGENS": A high-efficiency particulate arrestor (HEPA) or charcoal filters can be used to minimize amt of carcinogen in exhausted air ventilated safety cabinets, lab hoods, glove boxes or animal rooms ... Filter housing that is designed so that used filters can be transferred into plastic bag without contaminating maintenance staff is avail commercially. Filters should be placed in plastic bags immediately after removal ... The plastic bag should be sealed immediately ... The sealed bag should be labelled properly ... Waste liquids ... should be placed or collected in proper containers for disposal. The lid should be secured & the bottles properly labelled. Once filled, bottles should be placed in plastic bag, so that outer surface ... is not contaminated ... The plastic bag should also be sealed & labelled. ... Broken glassware ... should be decontaminated by solvent extraction, by chemical destruction, or in specially designed incinerators. /Chemical Carcinogens/
7.Handling and storage
7.1 Precautions for safe handling
Avoid contact with skin and eyes. Avoid formation of dust and aerosols. Avoid exposure - obtain special instructions before use.Provide appropriate exhaust ventilation at places where dust is formed. For precautions see section 2.2.
7.2 Conditions for safe storage, including any incompatibilities
Fireproof. Separated from strong oxidants. Cool. Store only if stabilized.Fireproof. Separated from strong oxidants. Cool. Store only if stabilized.
8.Exposure controls/personal protection
8.1 Control parameters
Occupational Exposure limit values
Recommended Exposure Limit: 10 Hr Time-Weighted Avg: 1 ppm.
Recommended Exposure Limit: Ceiling Value: 5 ppm.
Biological limit values
no data available
8.2 Appropriate engineering controls
Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end of workday.
8.3 Individual protection measures, such as personal protective equipment (PPE)
Eye/face protection
Safety glasses with side-shields conforming to EN166. Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU).
Skin protection
Wear impervious clothing. The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace. Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique(without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands. The selected protective gloves have to satisfy the specifications of EU Directive 89/686/EEC and the standard EN 374 derived from it.
Respiratory protection
Wear dust mask when handling large quantities.
Thermal hazards
no data available
9.Physical and chemical properties
Physical state | Vinyl fluoride, stabilized is a colorless gas with a faint ethereal odor. Shipped as a confined liquid under its vapor pressure. Any leak can either be liquid or vapor. Contact with the liquid can cause frostbite. Easily ignited. Vapors are heavier than air. Can asphyxiate by the displacement of air. Under prolonged exposure to fire or intense heat the containers may rupture violently and rocket. |
---|---|
Colour | Colorless gas [Note: Shipped as a liquefied compressed gas]. |
Odour | Faint, ethereal odor. |
Melting point/ freezing point | -160.5ºC |
Boiling point or initial boiling point and boiling range | -72ºC |
Flammability | Flammable GasExtremely flammable. |
Lower and upper explosion limit / flammability limit | Lower flammable limit: 2.6% by volume; Upper flammable limit: 21.7% by volume |
Flash point | Flammable gas |
Auto-ignition temperature | 460°C (USCG, 1999) |
Decomposition temperature | no data available |
pH | no data available |
Kinematic viscosity | 3.2347E-04 pascal/seconds (liquid) @ boiling point |
Solubility | Insoluble (NIOSH, 2016) |
Partition coefficient n-octanol/water (log value) | log Kow = 1.19 /Estimated/ |
Vapour pressure | 25.2 atm (NIOSH, 2016) |
Density and/or relative density | 0.615 g/cm3 |
Relative vapour density | 1.58 (Air= 1) |
Particle characteristics | no data available |
10.Stability and reactivity
10.1 Reactivity
no data available
10.2 Chemical stability
Stable under recommended storage conditions.
10.3 Possibility of hazardous reactions
Ignites in presence of heat or source of ignition.The vapour is heavier than air and may travel along the ground; distant ignition possible.VINYL FLUORIDE is light sensitive, peroxidizable monomer may initiate exothermic polymerization of the bulk material [Handling Chemicals Safely 1980. p. 958]. Sensitive to many oxidants.
10.4 Conditions to avoid
no data available
10.5 Incompatible materials
During ozonolysis of vinyl fluoride an explosive solid residue is produced, and the volatile ozonide, trapped at -63°C, may explode spontaneously or during removal by syringe.
10.6 Hazardous decomposition products
When heated to decomposition it emits toxic fumes of /hydrogen fluoride/.
11.Toxicological information
Acute toxicity
- Oral: no data available
- Inhalation: no data available
- Dermal: no data available
Skin corrosion/irritation
no data available
Serious eye damage/irritation
no data available
Respiratory or skin sensitization
no data available
Germ cell mutagenicity
no data available
Carcinogenicity
Evaluation: There is inadequate evidence in humans for the carcinogenicity of vinyl fluoride. There is sufficient evidence in experimental animals for the carcinogenicity of vinyl fluoride. Overall evaluation: Vinyl fluoride is probably carcinogenic to humans (Group 2A). In making the overall evaluation, the working group took into account the following evidence: Vinyl fluoride is closely related structurally to the known carcinogen, vinyl chloride. The two chemicals cause the same rare tumor (hepatic hemangiosarcoma) in experimental animals, which is also a tumor caused by vinyl chloride in humans.
Reproductive toxicity
no data available
STOT-single exposure
no data available
STOT-repeated exposure
no data available
Aspiration hazard
no data available
12.Ecological information
12.1 Toxicity
- Toxicity to fish: no data available
- Toxicity to daphnia and other aquatic invertebrates: no data available
- Toxicity to algae: no data available
- Toxicity to microorganisms: no data available
12.2 Persistence and degradability
no data available
12.3 Bioaccumulative potential
An estimated BCF of 2 was calculated for vinyl fluoride(SRC), using an estimated log Kow of 1.19(1) and a regression-derived equation(2). According to a classification scheme(3), this BCF suggests the potential for bioconcentration in aquatic organisms is low(SRC), provided the compound is not altered physically or chemically once released into the environment.
12.4 Mobility in soil
Using a structure estimation method based on molecular connectivity indices(1), the Koc for vinyl fluoride can be estimated to be 24(SRC). According to a classification scheme(2), this estimated Koc value suggests that vinyl fluoride is expected to have very high mobility in soil.
12.5 Other adverse effects
no data available
13.Disposal considerations
13.1 Disposal methods
Product
The material can be disposed of by removal to a licensed chemical destruction plant or by controlled incineration with flue gas scrubbing. Do not contaminate water, foodstuffs, feed or seed by storage or disposal. Do not discharge to sewer systems.
Contaminated packaging
Containers can be triply rinsed (or equivalent) and offered for recycling or reconditioning. Alternatively, the packaging can be punctured to make it unusable for other purposes and then be disposed of in a sanitary landfill. Controlled incineration with flue gas scrubbing is possible for combustible packaging materials.
14.Transport information
14.1 UN Number
ADR/RID: UN1860 | IMDG: UN1860 | IATA: UN1860 |
14.2 UN Proper Shipping Name
ADR/RID: VINYL FLUORIDE, STABILIZED |
IMDG: VINYL FLUORIDE, STABILIZED |
IATA: VINYL FLUORIDE, STABILIZED |
14.3 Transport hazard class(es)
ADR/RID: 2.1 | IMDG: 2.1 | IATA: 2.1 |
14.4 Packing group, if applicable
ADR/RID: unknown | IMDG: unknown | IATA: unknown |
14.5 Environmental hazards
ADR/RID: no | IMDG: no | IATA: no |
14.6 Special precautions for user
no data available
14.7 Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
no data available
15.Regulatory information
15.1 Safety, health and environmental regulations specific for the product in question
Chemical name | Common names and synonyms | CAS number | EC number |
---|---|---|---|
fluoroethene | fluoroethene | 75-02-5 | none |
European Inventory of Existing Commercial Chemical Substances (EINECS) | Listed. | ||
EC Inventory | Listed. | ||
United States Toxic Substances Control Act (TSCA) Inventory | Listed. | ||
China Catalog of Hazardous chemicals 2015 | Listed. | ||
New Zealand Inventory of Chemicals (NZIoC) | Not Listed. | ||
Philippines Inventory of Chemicals and Chemical Substances (PICCS) | Listed. | ||
Vietnam National Chemical Inventory | Not Listed. | ||
Chinese Chemical Inventory of Existing Chemical Substances (China IECSC) | Not Listed. |
16.Other information
Information on revision
Creation Date | Aug 17, 2017 |
---|---|
Revision Date | Aug 17, 2017 |
Abbreviations and acronyms
- CAS: Chemical Abstracts Service
- ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
- RID: Regulation concerning the International Carriage of Dangerous Goods by Rail
- IMDG: International Maritime Dangerous Goods
- IATA: International Air Transportation Association
- TWA: Time Weighted Average
- STEL: Short term exposure limit
- LC50: Lethal Concentration 50%
- LD50: Lethal Dose 50%
- EC50: Effective Concentration 50%
References
- IPCS - The International Chemical Safety Cards (ICSC), website: http://www.ilo.org/dyn/icsc/showcard.home
- HSDB - Hazardous Substances Data Bank, website: https://toxnet.nlm.nih.gov/newtoxnet/hsdb.htm
- IARC - International Agency for Research on Cancer, website: http://www.iarc.fr/
- eChemPortal - The Global Portal to Information on Chemical Substances by OECD, website: http://www.echemportal.org/echemportal/index?pageID=0&request_locale=en
- CAMEO Chemicals, website: http://cameochemicals.noaa.gov/search/simple
- ChemIDplus, website: http://chem.sis.nlm.nih.gov/chemidplus/chemidlite.jsp
- ERG - Emergency Response Guidebook by U.S. Department of Transportation, website: http://www.phmsa.dot.gov/hazmat/library/erg
- Germany GESTIS-database on hazard substance, website: http://www.dguv.de/ifa/gestis/gestis-stoffdatenbank/index-2.jsp
- ECHA - European Chemicals Agency, website: https://echa.europa.eu/
Hangzhou DayangChem Co., Ltd
CHINA
Purity: 98%
Lead Time: 7 Day(s)
Price: -